How do I enable UDP port 137?

Step 1: Open the Control Panel Step 2: Click on Windows Firewall/ Windows Defender firewall Step 3: Navigate to advanced settings. Step 4:Right click on inbound rules and click on new rule. Step 6:Select port and press next Step 7:Specify the port 137 under specific local ports, select UDP and press next.

How do I fix destination unreachable port unreachable?

How to Fix Destination Port Unreachable Error?

  1. Ping the Address From a Different IP address. To check whether the remote device banned your IP address, you need to send ping packets from a different network address.
  2. Disable the Proxy and VPN Services on your Device.
  3. Check for Protocol Mismatch.

How do I fix UDP connection?

To do this, follow these steps:

  1. Click Start, type wf. msc in the Search programs and files box, and then click wf. msc under Programs.
  2. Click Inbound Rules.
  3. Locate and then select the Failover Clusters (UDP-In) rule.
  4. Disable or delete the Failover Clusters (UDP-In) rule.

What is the protocol for port 137?

Side note: UDP port 137 uses the Datagram Protocol, a communications protocol for the Internet network layer, transport layer, and session layer. This protocol when used over PORT 137 makes possible the transmission of a datagram message from one computer to an application running in another computer.

What are ports 137 and 138 used for?

Ports 137, 138, and 139 are used by NetBIOS, which does not support IPv6. CIFS is required for Windows file service. You can disable CIFS by issuing the cifs terminate command on your storage system console.

What UDP ports are open?

Commonly Open Ports

udp 161 0.54% 5363
udp 69 0.02% 158
udp 5353 0.01% 55
udp 9300 0% 22
udp 12203 0% 19

What causes destination unreachable?

If you try to ping your router from a computer on the Local Area Network (LAN) and you get a response – destination host unreachable, this means that your computer is not getting an IP address from the router. You can then investigate the IP address settings on the device and verify the connections.

What are possible reasons that would cause a destination to be unreachable?

Any one of the reasons listed below can get you to the ICMP Echo message Destination Host Unreachable.

  • Your Default Gateway doesn’t know the route to the destination IP address.
  • Packet Routing issue on Remote gateway.
  • The destination host might be down.
  • Loose Connection.
  • Wrong Firewall Settings.

How do I enable UDP on my router?

Opening TCP/UDP port

  1. Locate your router’s IP address.
  2. Head over to your router’s settings.
  3. Enter your credentials (username and password).
  4. Look around for the Port Forwarding tab.
  5. Open your preferred port—for example, type 8080 to open port 8080.
  6. Save your settings.

Is UDP blocked by default?

firewall. UDP can be blocked, by default, on many types of firewall, because it’s (essentially) unsolicited network traffic. There’s no ACK (like in TCP), so as long as there’s an open port, UDP traffic could be allowed to flood a network (and a flooded network is bad!).

What type of traffic is normally seen over UDP port 137?

NBNS
Protocol dependencies UDP: Typically, NBNS uses UDP as its transport protocol. The well known UDP port for NBNS traffic is 137. TCP: NBNS can also use TCP as its transport protocol for some operations, although this might never be done in practice. The well known TCP port for NBNS traffic is 137.

How do I check if my UDP port is blocked?

“nc -uvz ip port” isn’t somehow accurate, you probably should use “nmap -sU -p port ip” , if the result shows “open” then the udp port probably is open, if it shows “open|filtered” then probably it is closed or filtered.

What is port 137 on UDP?

UDP Port 137. Here is what we know about protocol UDP Port 137. If you have information on UDP port 137 that is not reflected on this page, simply leave a comment and we’ll update our information. PORT 137 – Information. Port Number: 137. TCP / UDP: UDP. Delivery: No. Protocol / Name: [Malware known as Msinit] netbios-ns.

What is udp137?

UDP 137 is used by NetBIOS File sharing in Windows 7. Depending on what you do while you are using Remote Desktop on your network, it might invoke the UDP137. If it does not impede anything functional that you need to do, leave it alone.

What is port 137 on the NetBIOS Name Service?

PORT 137 – Information. Port Number: 137. TCP / UDP: UDP. Delivery: No. Protocol / Name: [Malware known as Msinit] netbios-ns. Port Description: [malware info: Msinit] NETBIOS Name Service.

By